The maintenance tip of Cummins CCEC diesel engine

ချုံကင်း Cummins အင်ဂျင် Co., Ltd. တရုတ်-အမေရိကန် ဖက်စပ်လုပ်ငန်းတစ်ခုဖြစ်သည်။, အောက်တိုဘာလတွင် တည်ထောင်ခဲ့သည်။ 1995, အာဇာနည်ကုန်းတွင် တည်ရှိသည်။’ Shapingba ခရိုင်၏သင်္ချိုင်း, ချုံကင်း. တရုတ်နိုင်ငံ၏ မိခင်ကုမ္ပဏီမှာ Chongqing Mechanical ဖြစ်သည်။ & လျှပ်စစ်ကုမ္ပဏီ, LTD, နိုင်ငံခြားမိခင်ကုမ္ပဏီက Cummins ဖြစ်ပါတယ်။ (တရုတ်) ရင်းနှီးမြှုပ်နှံမှု Co., LTD, ကိုင်ဆောင်မှုတစ်ခုစီနှင့် 50% ရင်းနှီးမြှုပ်နှံမှု. ကုမ္ပဏီထက် ပိုပါတယ်။ 1400 ဝန်ထမ်းများ. ချုံကင်း Cummins, formerly known as Chongqing Automobile Engine Factory, began to design and manufacture diesel engines in the 1950s.

The company mainly produces cummins N, K, M three series of diesel engines, မီးစက်အစုံနှင့် အခြားပါဝါအစုံများ, အင်ဂျင်ပါဝါလွှမ်းခြုံမှုအကွာအဝေး 145-1343KW, annual capacity of 15,000 sets. ထုတ်ကုန်များသည် လေးလံသောယာဉ်များအတွက် သင့်လျော်သည်။, ဘတ်စ်ကားကြီးတွေ, ဆောက်လုပ်ရေးစက်ပစ္စည်း, သတ္တုတူးဖော်ရေးစက်, ရေနံစက်, မီးရထားစက်, ဆိပ်ကမ်းစက်, ပုံသေနှင့်မိုဘိုင်းဒီဇယ်မီးစက်အစုံပါဝါဘူတာရုံ, Marine propulsion power set နှင့် auxiliary power set, pump power set နှင့် အခြားသော power set များ.

When dealing with the maintenance of the above Cummins diesel engine, the following tips will be helpful for your engine.

Use fuel oil, lubricating oil and coolant as specified in the specification.
Chongqing Cummins co., Ltd. uses the latest technology and the best quality components to manufacture engines. So when it comes to replacing parts, we recommend — always use Cummins genuine engine parts.

During operation, pay close attention to whether the following conditions occur in the engine. If any of these items appear suddenly, ပျက်ကွက်ခြင်း၏ လက္ခဏာဖြစ်ဖွယ်ရှိသည်။. Please check and repair in time. Poor engine start or stop.
Abnormal vibration.
One power shortage.
Abnormal noise.

oil consumption increases.
A sudden change in working pressure and temperature.
fuel consumption increases.
Exhaust smoke degree is too large.
Leakage of fuel oil or water.
Start engine properly

To avoid damage to the starter, do not leave the starter running for more than 20 စက္ကန့်. There should be an interval of 2 minutes between two starts.

Within 10 seconds after starting. All alarm lights on the instrument should be turned off. Otherwise check or stop as soon as possible.
Do not idle the engine for too long. Idle running time is too long (ထက်ပိုပြီး 10 မိနစ်များ), may lead to the following faults, or even damage to the engine.

Black oil is leaking from a exhaust pipe
1. Increased fuel consumption
One oil was diluted with diesel
A shorter maintenance interval
Carbon accumulation in one cylinder
A critical part failed
One valve is stuck
Proper engine operation

Check oil pressure, coolant temperature and other engine parameters daily through OEM panel. To make sure they work properly. Check the panel for any alarm information. Take appropriate action to correct alert status or contact the nearest Chongqing Cummins dealer.

Check the OEM panel readings frequently. If the pressure or temperature does not meet the technical specifications, shut down the engine immediately.

Correct engine shutdown

After the engine runs at full load, the engine must idle for 3-5 ရပ်တန့်မီမိနစ်. This is to allow components such as pistons, cylinders, bearings and superchargers to cool sufficiently to avoid damaging the engine.

Proper engine maintenance
■ Chongqing Cummins recommends that the engine be maintained according to the maintenance procedures in the operation and maintenance manual. Repeat all work of the previous maintenance level when performing a certain level of maintenance.
If the engine operating environment temperature is below -18 ° C [0°F] or above 38 ° C [100°F], the maintenance interval should be shortened. Work in dusty environment, or frequently shut down. It also needs to shorten the time between maintenance.
Some maintenance procedures require special tools or must be performed by qualified technicians.
If the system is equipped with parts or accessories not produced or provided by Chongqing Cummins Company. Refer to the maintenance suggestions of the component manufacturer.

Maintenance procedures (once A day) Grade A
Crankcase breathing tube – Check for mud, debris or ice
Oil level – check
Fuel/water separator – Drain water from the separator until clean fuel oil is seen
Remote installation of fuel filter (electronically controlled engine) – water storage in the discharge system
Intake pipe – check, ပျက်စီးလျှင်, loose clamp, replace or tighten clamp
Drive belt – check for breakage and adjust tension.
Air filter resistance — စစ်ဆေးပါ။ (red/green)
Coolant level — check
Check the air filter element every day

★ Reserve space for expansion
Maintenance procedures (every 250 hours or 6 months) Grade B
Oil change
Replacement of fuel filter (mechanical engine)
Replace the oil filter
Check the cooling fan
Replace the Level 1 fuel filter (electronically controlled engine)
Replace stage 2 fuel filter (electronically controlled engine)
မှတ်ချက်: Do not fill the new stage 2 filter with fuel.
Replace coolant filter
Check coolant additive (DCA)
Maintenance procedures (every 1500 hours or 1 year) Grade C
Fuel injector stroke, valve clearance – one adjustment
Cooling fan belt tensioner – – grease filling
Radiator and hose – check whether they can be reused
Engine front support seat – grease filling
Front and rear bracket mounting bolts – check
Crankcase breathing apparatus – clean and check for continued use
Maintenance procedures (every 6000 hours or 2 နှစ်များ) Grade D
One by one fuel pump calibration
Cooling system – add detergent inside to remove scale
Fuel injector — calibration
Silicone oil shock absorber – check
တာဘိုချာဂျာ – check for continued use
Fan hub – – စစ်ဆေးပါ။